|
Burlington Northern Railroad Bridge 9.6 or BNSF Railway Bridge 9.6, also known as the Columbia River Railroad Bridge, is through truss railway bridge across the Columbia River, between Portland, Oregon, and Vancouver, Washington, owned and operated by BNSF Railway.〔 Built by the Spokane, Portland and Seattle Railway (SP&S) and completed in 1908, it was the first bridge of any kind to be built across the lower Columbia River,〔. (June 26, 1908). ''The Morning Oregonian'', p. 11. Retrieved 2014-06-21.〕 preceding the first road bridge, the nearby Interstate Bridge, by a little more than eight years. The long〔 bridge has a swing span, which pivots on its base to allow for the passage of taller ships. The bridge carries two railroad tracks, which are used by BNSF, Union Pacific Railroad, and Amtrak. It is one of only two surviving swing-span bridges in the Portland metropolitan area, which once had several bridges of that type.〔 The other survivor is another BNSF bridge located nearby, on the same line and built at the same time, the Oregon Slough Railroad Bridge (also known as BNSF Railway Bridge 8.8).〔 The 9.6 in the name is the distance, in miles, from Portland's Union Station, the same as for Bridge 5.1 (across the Willamette River) and Bridge 8.8 on the same line.〔 ==History== Construction of a single-track railroad bridge at the same location was started in 1890, engineered by George S. Morison〔 for the Portland & Puget Sound Railroad Company〔("Builds North to the Sound" ). (February 13, 1906). ''The Morning Oregonian'', p. 12.〕 (affiliated with Union Pacific), but that project was abandoned at an early stage.〔 In 1905, another crossing of the Columbia River was proposed, this time by the Northern Pacific Railway (NP), for use by the newly formed Portland & Seattle Railway. The Portland & Seattle had been formed jointly by NP and Great Northern Railway,〔("Two Roads Come On North Bank: Northern Pacific and Great Northern" ). (September 17, 1905). ''The Sunday Oregonian'', p. 1. Retrieved 2014-06-21.〕 to build and ultimately operate new railroad lines from Portland to Seattle and Portland to Spokane, but was renamed ''Spokane'', Portland & Seattle Railway (SP&S) – in early 1908,〔. (January 30, 1908). ''The Morning Oregonian'', p. 11. Retrieved 2014-06-21.〕 before opening any track sections – after construction of the Portland–Spokane line got under way before the Seattle line.〔("History of North Bank Road" ). (November 6, 1908). ''The Morning Oregonian'', p. 12.〕 The planned new railroad was commonly referred to as the "North Bank road"〔〔 (road being short for railroad or railroad line), or North Bank line, because the Seattle line would follow the Columbia River's north bank as far as Kelso and the Spokane line would also follow the north bank, running east from Vancouver. East from Portland, the south bank of the Columbia already had a rail line, owned by the Oregon Railroad and Navigation Company (later absorbed by Union Pacific Railroad). The bridge was part of an overall planned new line from Vancouver to Northwest Portland, which included three major new bridges: the Columbia River Bridge, Oregon Slough Bridge and Willamette Drawbridge. Northern Pacific hired bridge builder Ralph Modjeski to design all three.〔〔("Bridge the River: Ralph Modjeski Here to Supervise Work—Spanning the Columbia" ). (January 10, 1906). ''The Morning Oregonian'', p. 11.〕 On November 14, 1905, the SP&S board approved Modjeski's recommendations. Plans for the bridges were submitted to the War Department, and eventually approved in February 1906.〔 Pier 2 of the Columbia River bridge, the pier on which the swing-span section pivots, was built as part of the canceled 1890 project, and was incorporated into the plans for the 1906 bridge.〔〔 The first work was performed on February 8, 1906, when work crews began framing the caissons. The steel was fabricated by the American Bridge Company of New York. Construction took approximately 26 months. Steel construction at the site began on June 15, 1907.〔 Structural work on the bridge was completed in June 1908,〔 but its opening to traffic was delayed by problems concerning installation of the heavy machinery required to turn the huge swing span on the new Willamette River bridge located on the same line.〔("Road to Open October 15: Tentative Date for Inauguration of Service on North Bank Line" ). (October 4, 1908). ''The Sunday Oregonian'', Section 3, p. 7.〕 The first train crossed the span on October 23, 1908,〔"First Train Crosses Bridges". (October 24, 1908). ''The Morning Oregonian'', p. 4.〕 and the bridge opened for regular use in November 1908.〔("Begin New Service: North Bank Road Schedule to Go Into Effect Tuesday" ). (November 11, 1908). ''The Morning Oregonian'', p. 16. Retrieved 2014-06-21.〕 This completed the initial SP&S route, between Portland and Pasco. Ownership and operation of the bridge passed to the Burlington Northern Railroad (BN) in 1970, when SP&S, Northern Pacific and other railroads merged to form BN. At the end of 1996, BN merged with the Atchison, Topeka and Santa Fe Railway (Santa Fe), becoming the Burlington Northern and Santa Fe Railway〔"Merger: E. Pluribus Unum". ''RailNews'', March 1997, p. 87. Pentrex. ISSN 1091-2436.〕 (officially shortened to BNSF Railway in 2005). 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「Burlington Northern Railroad Bridge 9.6」の詳細全文を読む スポンサード リンク
|